10  Machine Coord
11  SpindleOn
12  MistOn
13  FloodOn
14  Jog Cont.
15  Jog Incr.
16  WorkOffsets Display.
17  Feed OverRide
18  Simulation On 
19  Emergency Input Active
20  A axis Diam. Comp.
21  B Axis Diam  Comp.
22  C Axis Diam  Comp.
23  Softlimits on.
24  THC On
25  Spindle Accelerating
26  Spindle Decelerating
27  ToolPath On
28  Tool Offset in effect
29  Work Offset in effect
30  Throttle used for Override
31  Throttle used for Jog speed
32  BackLash on.
33  AutoLimits override in effect
34  Limits switches disenganged
35  Input#4 single step engaged
36  Torch OK active
37  Torch Up Active
38  Torch Down Active 
39  Units/Rev Mode 
40  Units/Min Mode
41  X Scaling Active
42  Y Scaling Active
43  Z Scaling Active
44  A Scaling Active
45  B Scaling Active
46  C Scaling Active
47  Jog Follow Active
48  Absolute Coord mode.
49  Incremental Coord Mode
50  Threading Sync Active
51  LaserTriggering  Active
52  Z Inhibit Active
53  Ignoring Tool Change M6
54  Continuous Velocity Mode.
55  Repeat runs holding
56  Exact Stop Mode.
57  MPG Jog Mode
58  Continuous Jog Mode
59  X Axis MPG mode
60  Y Axis MPG mode
61  Z Axis MPOG mode
62  A Axis MPG Mode
63  B Axis MPG Mode
64  C Axis MPG Mode
65  Optional Stop M1 enabled
66  Block Delete mode enabled 
67  Offline Active 
68  Actual Spindle speed in Use. 
69  Waiting for thread trigger point 
70  Plunging Disabled
71  Spindle Speed Stable
72  IJ Mode Abs
73  IJ Mode Incremental
74  TeachFile is open
75  G92 in effect
77  OUTPUT4 Active
78  OUTPUT5 Active
79  Output6 Active
80  Engine in Pause state
81  Tangental control in effect
82  Single Step mode active
83  Jog Enabled
84  CV Feedrate descriminator enabled
85  Enhance pulseing Off
86  X Axis Enabled
87  Y Axis Enabled
88  Z Axis Enabled
89  A Axis Enabled
90  B Axis Enabled
91  C Axis Enabled
92  Diameter Mode enabled
93  MultiSlot Spindle Input enabled
94  HotKeys Enabled
95  Units/Minute mode
96  Units/Rev Mode
97  Running in Reverse
98  X MPG enabled MPG #2
99  Y MPG Enabled MPG #2
100 Z MPG enabled MPG #2
101 A MPG Enabled MPG #2
102 B MPG enabled MPG #2
103 C MPG Enabled MPG #2
104 Dual MPG Taper Mode enabled
105 Dual MPG Jog Mode enabled
106 MPG Velocity Mode
107 G96 mode in effect
108 Coordinate system Rotated
109 Rapid Speed OverRide
110 Formula corrections on. 
111 Partial move holding
112 Running in Reverse
113 Feedrate Bypass Enabled
114 Front toolpost active
115 Rear Toolpost active 
116 Spindle running in CCW
117 MPG Velocity mode selected) 
118 MPG Vel/Step mode enabled
119 MPG Single Step enabled
120 MPG Multistep enabled
121 External XJog++ active
122 External XJog-- Active 
123 External YJog++ active
124 External YJog-- Active 
125 External ZJog++ active
126 External ZJog-- Active 
127 External AJog++ active
128 External AJog-- Active 	           
129 Toolpath Zoom locked on
130 Toolpath PanState locked on
131 MPG #3 X axis Active
132 MPG #3 Y axis Active
133 MPG #3 X axis Active
134 MPG #3 Y axis Active
135 MPG #3 X axis Active
136 MPG #3 Y axis Active
137 Printer port bit 0
138 Printer port bit 1
139 Printer port bit 2
140 Printer port bit 3
141 Printer port bit 4
142 Printer port bit 5
143 Printer port bit 6
144 Printer port bit 7
145 Printer port bit 8
146 Printer port bit 9
147 Printer port bit 10
148 Printer port bit 11
149 Printer port bit 12
150 Printer port bit 13
151 Printer port bit 14
152 Printer port bit 15
153 Printer port bit 16
154 Printer port bit 17
155 Printer port bit 18
156 Printer port bit 19
157 Printer port bit 20
158 Printer port bit 21
159 Printer port bit 22
160 Printer port bit 23
161 Printer port bit 24
162 Macro In progress
999 Machine Is Moving
500 GRex Heartbeat
501 GRex Still
502 GRex Ended Queue
503 GRex Mavg queue drained
504 Grex Paused
505 GRex Purging
506 GRex Halted
507 GRex Global Rate Reg, OK
508 GRex X Axis Homed
509 GRex Y Axis Homed
510 GRex Z Axis Homed
511 GRex A Axis Homed
512 GRex B Axis Homed
513 GRex C Axis Homed 
514 GRex halt monitor pin 1
515 GRex halt monitor pin 2
516 GRex halt monitor pin 3
517 GRex halt monitor pin 4
518 GRex halt monitor pin 5
519 GRex halt monitor pin 6
520 GRex halt monitor pin 7
521 GRex halt monitor pin 8
522 GRex halt monitor pin 9
523 GRex halt monitor pin 10
524 GRex halt monitor pin 11
525 GRex halt monitor pin 12
526 GRex halt monitor pin 13
527 GRex halt monitor pin 14
528 GRex halt monitor pin 15
529 GRex halt monitor pin 16
530 GRex Queue Full
531 GRex Sequence Error
532 GRex Packet Loss Diag Mode
533 GRex Pin 1 Active
534 GRex Pin 2 Active
535 GRex Pin 3 Active
536 GRex Pin 4 Active
537 GRex Pin 5 Active
538 GRex Pin 6 Active
539 GRex Pin 7 Active
540 GRex Pin 8 Active
541 GRex Pin 9 Active
542 GRex Pin 10 Active
543 GRex Pin 11 Active
544 GRex Pin 12 Active
545 GRex Pin 13 Active
546 GRex Pin 14 Active
547 GRex Pin 15 Active
548 GRex Pin 16 Active
549 GRex Pin 17 Active
550 GRex Pin 18 Active
551 GRex Pin 19 Active
552 GRex Pin 20 Active
553 GRex Pin 21 Active
554 GRex Pin 22 Active
555 GRex halt monitor pin 17
556 GRex halt monitor pin 18
557 GRex halt monitor pin 19
558 GRex halt monitor pin 20
559 GRex halt monitor pin 21
560 GRex halt monitor pin 22
561 GRex Pin 1 Out Active
562 GRex Pin 2 Out Active
563 GRex Pin 3 Out Active
564 GRex Pin 4 Out Active
565 GRex Pin 5 Out Active
566 GRex Pin 6 Out Active
567 GRex Pin 7 Out Active
568 GRex Pin 8 Out Active
569 GRex Pin 9 Out Active
570 GRex Pin 10 Out Active
571 GRex Pin 11 Out Active
572 GRex Pin 12 Out Active
573 GRex Pin 13 Out Active
574 GRex Pin 14 Out Active
575 GRex Pin 15 Out Active
576 GRex Pin 16 Out Active
800 EStop Conditon Active;
801 MM Mode active
802 Inch Mode Active
803 program not in Stop Condition
804 Program Running
805 Planner Paused
806 ToolChange Wait
807 X Homed
808 Y Homed
809 Z Homed
810 A Homed
811 B Homed
812 C Homed
813 Dwell in effect    
814 Joystick On
815 Softlimits On
816 Machine Coorindates On
817 Exact Stop Condition
818 Work Offsets in Effect
819 Incremental Jog
820 Continous Jog
821 OUTPUT1 Active
822 OUTPUT2 Active
823 OUTPUT3 Active
824 OUTPUT4 Active
825 Probe Input Active
826 Index Input Active
827 LimitOverRide Input Active
828 X++ Limit Active
829 X-- Limit Active
830 X Home Active
831 Y++ Limit Active
832 Y-- Limit Active
833 Y Home Active
834 Z++ Limit Active
835 Z-- Limit Active
836 Z Home Active
837 A++ Limit Active
838 A-- Limit Active
839 A Home Active
840 B++ Limit Active
841 B-- Limit Active
842 B Home Active
843 C++ Limit Active
844 C-- Limit Active
845 C Home Active
846 Enable1 Active
847 Enable2 Active
848 Enable3 Active
849 Enable4 Active
850 Enable5 Active
851 Enable6 Active
852 OUTPUT1 Active
853 OUTPUT2 Active
854 OUTPUT3 Active
855 DigTrigger output Active


 
 